How to find support and resistance levels
Support and resistance are price zones where the market reacted more than once. You can find them by marking swing highs and lows on a large chart, then drawing a band no wider than about one ATR.
The short answer
To find support and resistance, start on a large chart such as 1D or 1W, look for swing highs and lows where price reacted more than once, and draw a band around each group, not a single line. The band should be no wider than about one ATR, and you should lean on closes rather than on wicks alone. Then count the touches inside the band: the more there are, the clearer the zone looks on the chart. All of this describes what already happened on the chart, not a promise of what comes next. The goal of these steps is to learn to read the chart yourself, and then to compare your reading with what the engine shows.
Step one: zoom out and find the swings
Start with the daily chart, 1D, then open the weekly, 1W, to see the wider picture. The larger the timeframe, the less noise there is and the clearer the important places become. If you begin on a small chart such as 1H, you will find dozens of weak zones that mean little. This is also a good habit because places where price reacted on a large chart stay visible for longer. Remember that the daily close is at 00:00 UTC, and that a candle still forming does not count.
Next, look for the swings. A swing high is a candle whose high is above the highs of the candles next to it on both sides. A swing low is a candle whose low is below the lows of its neighbours. Mark these points from left to right, and do not try to mark every small bump; keep to the clear ones. The lesson on trend and swings shows how the same points are used to read the trend.
Step two: look for repeated reactions and draw a band
Now look at the points you marked. If several highs or lows sit in roughly the same price area, the market reacted there more than once. If the area is below the current price it is a support; if it is above, it is a resistance. One reaction means little, but two or three in the same place deserve attention, because they show the market came back to that band more than once.
Price rarely turns at one exact value, so do not draw a thin line. Follow these steps:
- Group the highs or lows that sit close together into one set.
- Draw the band from the lowest point of the set to the highest, and prefer measuring by bodies and closes rather than by long wicks alone.
- Check that the band is no wider than one ATR; otherwise it is too wide to be a single zone.
- Count the reactions inside the band. That is the number of touches.
When you finish, you have a band with an upper edge, a lower edge and a touch count. A band with many touches is one the market has respected often; one with two touches is a lighter observation. Both describe past behaviour, and either one can break. The lesson on ATR explains how the average candle range is measured, which is the yardstick we use for the maximum width.
A live example from the engine
The block below is read from Cryptokly's engine, not typed by hand. It shows the nearest support and the nearest resistance zone on each of the five BTC/USDT charts. The engine groups nearby swings into a band no wider than one ATR, counts the touches, and uses closed candles only.
| Timeframe | Support | Price | Resistance |
|---|---|---|---|
| 1M | 60,000.0060,000.00 · 1 touch | Between support and resistance | 82,850.0082,850.00 · 1 touch |
| 1W | 60,000.0060,000.00 · 1 touch | Between support and resistance | 62,510.2862,510.28 · 1 touch |
| 1D | Open range on this chart | Between support and resistance | 62,006.0062,006.00 · 1 touch |
| 4H | Open range on this chart | Between support and resistance | 63,905.0163,905.01 – 64,080.80 · 2 touches |
| 1H | 61,428.2661,290.58 – 61,428.26 · 2 touches | Between support and resistance | 62,062.9762,062.97 – 62,639.52 · 5 touches |
Read one row at a time, because each row belongs to one chart. Compare what you drew with what the engine shows: do the edges of your band sit near the edges of its band? If they differ, that is normal, because you may have picked other candles. A comparison is not a test you pass or fail; its value is in understanding why the engine chose a particular band. If a row is missing for a chart, the engine found no zone near the price at the time of the run.
Related lessons and coin pages
To go deeper, read the lesson on support and resistance, which explains how Cryptokly computes zones. To see what happens when price closes beyond a band, read false breakout vs real breakout. You can see the zones of each coin on its page: Bitcoin, Solana and BNB.
Common mistakes
- Drawing a thin line instead of a band. Price does not turn at one exact value, so use the whole band; its edges matter as much as its middle.
- Starting on a small chart. 1H zones are many and weak, so start on 1D or 1W and then go down to the smaller ones.
- Counting every wick as a touch. A wick that no closes support is a weaker observation than a band where many candles closed.
- Forgetting the risk. Crypto trading carries a real risk of losing money, up to the whole amount invested, and a well-drawn band does not remove it.
Questions
How many touches are enough for a zone to matter?
There is no fixed number. Two touches make a zone a light observation, and more touches make it clearer on the chart. But the count only describes the past and says nothing about the next candle, so read it together with the timeframe you are looking at.
Can support turn into resistance?
Yes, and it happens often on charts. If candles close beyond a support band, that is, below it, the same band can afterwards be read as a resistance above price. The band is the same one; only its name changes with where price sits relative to it, which is why the closed candles matter more than the label.
Does my drawing have to match what the engine shows?
No. The engine uses fixed rules to find and group swings, and you may pick other candles. What matters is that your choice rests on closes, repeated reactions and a reasonable width.